What pre-work needs to be done before PCB design

Views: 3     Author: Site Editor     Publish Time: 2021-04-10      Origin: Site Inquire

  Before starting the wiring, the PCB design should be carefully analyzed and the tool software should be carefully set, which will make the PCB design more in line with the requirements. Next, Shenzhen VIASION Electronic Technology Co., Ltd. will introduce to you what preparatory work needs to be done before PCB design?


Preliminary work that needs to be done before PCB design

  1. Determine the number of layers of the PCB

  The size of the circuit board and the number of wiring layers need to be determined at the early stage of PCB design. The number of wiring layers and the STack-up method will directly affect the wiring and impedance of the printed lines. The size of the board helps to determine the stacking method and the width of the printed line to achieve the desired PCB design effect. At present, the cost difference between multi-layer boards is very small. It is better to use more circuit layers and evenly distribute copper when starting PCB design.


  2. PCB design rules and restrictions

  To successfully complete the wiring task, wiring tools need to work under the correct rules and restrictions. To classify all signal lines with special requirements, each signal class should have a priority. The higher the priority, the stricter the rules. The rules involve the width of printed lines, the maximum number of vias, parallelism, mutual influence between signal lines, and layer restrictions. These rules have a great influence on the performance of wiring tools.


  Careful consideration of PCB design requirements is an important step for successful wiring.


  3. The layout of the components

  In the optimal assembly process, PCB design for manufacturability (DFM) rules will restrict component layout. If the assembly department allows the components to move, the circuit can be appropriately optimized, which is more convenient for automatic wiring. The defined rules and constraints will affect the layout of the PCB design. The automatic routing tool only considers one signal at a time. By setting the routing constraints and setting the layer of the signal line, the routing tool can complete the routing as the PCB designer envisioned.


  For example, for the layout of the power line: ① In the PCB layout, the power decoupling circuit PCB should be designed near the relevant circuits, and not placed in the power section, otherwise it will not only affect the bypass effect, but also flow on the power line and ground line. Excessive pulsating current can cause interference; ②For the power supply direction inside the circuit, power should be supplied from the final stage to the previous stage, and the power filter capacitor of this part should be arranged near the final stage; ③For some main current channels, such as debugging When disconnecting or measuring current during testing, current gaps should be arranged on the printed wires during layout.


  In addition, it should be noted that the regulated power supply should be arranged on a separate printed circuit board as much as possible during the layout. When the power supply and the circuit share a printed circuit board, in the layout, it should be avoided that the stabilized power supply and the circuit components are mixed or the power supply and the circuit share the ground wire.


  Because this kind of wiring is not only easy to produce interference, but also unable to disconnect the load during maintenance, only part of the printed wires can be cut at that time, thereby damaging the printed board.


  4. Fan-out PCB design

  In the fan-out PCB design stage, each pin of the surface mount device should have at least one via, so that when more connections are needed, the circuit board can perform inner-layer connections, online testing, and circuit reprocessing.


  In order to maximize the efficiency of the automatic routing tool, the largest via size and printed line must be used as much as possible, and the interval is set to 50mil. Use the via type that maximizes the number of routing paths. After careful consideration and prediction, the PCB design of the circuit online test can be carried out at the early stage of the PCB design and realized at the later stage of the production process.


  Determine the type of via fan-out according to the wiring path and circuit online testing. Power and ground will also affect the wiring and fan-out PCB design.


  5. Manual wiring and processing of key signals

  Manual wiring is an important process of PCB design now and in the future. Using manual wiring helps automatic wiring tools to complete the wiring work.


  By manually routing and fixing the selected network (net), a path that can be used for automatic routing can be formed.


  The key signals are wired first, either manually or in combination with automatic wiring tools. After the wiring is completed, the relevant engineering and technical personnel will check the signal wiring. After the inspection is passed, the wires will be fixed, and then the remaining signals will be automatically wired.


  Due to the existence of impedance in the ground wire, it will bring common impedance interference to the circuit. Therefore, do not connect any points with a grounding symbol at will during wiring, which may cause harmful coupling and affect the operation of the circuit.


  At higher frequencies, the inductance of the wire will be several orders of magnitude larger than the resistance of the wire itself. At this time, even if only a small high-frequency current flows through the wire, a certain high-frequency voltage drop will occur. Therefore, for high-frequency circuits, the PCB layout should be arranged as compactly as possible, and the printed wires should be as short as possible.


  There are mutual inductance and capacitance between the printed wires. When the working frequency is high, it will cause interference to other parts, which is called parasitic coupling interference. The suppression methods that can be adopted are: ① Shorten the signal wiring between all levels as much as possible; ② Arrange the circuits of all levels in the order of the signals to avoid crossing the signal lines of each level; ③ The wires of two adjacent panels should be perpendicular or crossed. Parallel; ④When signal wires are to be laid in parallel in the board, these wires should be separated by a certain distance as much as possible, or separated by ground wires and power wires to achieve the purpose of shielding.


  6. Automatic wiring

  For the wiring of key signals, you need to consider controlling some electrical parameters during wiring, such as reducing distributed inductance, etc. After understanding what input parameters the automatic wiring tool has and the influence of input parameters on the wiring, the quality of the automatic wiring can be obtained to a certain extent. Guarantee.


  General rules should be used when automatically routing signals. By setting restriction conditions and prohibiting wiring areas to limit the layers used for a given signal and the number of vias used, the wiring tool can automatically route according to the engineer's PCB design ideas. After setting the constraints and applying the created rules, the automatic routing will achieve similar results as expected. After a part of the PCB design is completed, it will be fixed to prevent it from being affected by the subsequent routing process.


  The number of wiring depends on the complexity of the circuit and the number of general rules defined. Today's automatic wiring tools are very powerful and can usually complete 100% of the wiring. However, when the automatic wiring tool has not completed all signal wiring, it is necessary to manually route the remaining signals.


  7. Arrangement of wiring

  For some signals with few constraints, the wiring length is very long. At this time, you can first determine which wiring is reasonable and which wiring is unreasonable, and then manually edit to shorten the signal wiring length and reduce the number of vias.

ISO9001:2015 | ISO13485:2016 | UL Certificate | Certified IPC Member | ISO14001:2015 | RoHS COC | REACH COC | Conflict Minerals

Social Community

Join our Social Community and keep in touch with all our latest technology investments, current news, upcoming events, and promotions.
Copyright@ 2007-2022 Viasion Technology Co., Ltd.